Jump to content

BigTuna117

Basic Members
  • Content Count

    245
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by BigTuna117

  1. Thanks! It takes at least 15 years off of the "aged look" of the rig, I think.
  2. So today I decided to take the rig for a test spin, just to see how it would perform under sustained load on our first day in the triple-digits. One of the great things (and one of the worst things, sometimes) about living here is all of the hills and steep climbs a vehicle has to make under acceleration or in a sustained manner. That's partly why most major auto manufacturers will actually use this area as a testbench for figuring out cooling systems on early model & prototype vehicles. I decided to put the Jeep through it's paces, and test out the new cooling system. I used a route I call the "torture loop" because it includes a mixture of sustained hill climbs, stop/start points in awkward places, highway speeds, street speeds, smooth/rough roads, etc. In reality, this loop does a great job of testing cooling, suspension, brakes, and tires all at once! I actually have some metrics to compare to, and for each of the recording "points" I generated when I was testing the last cooling revamp, the Jeep actually scored around 10-15 degrees cooler than it did previously! The new gauges also provide some excellent insight into what the transmission and oil are doing during these tests. The Good: The electric fan system. It does an excellent job of ramping up and down to control the temperature of the engine, and appears to sit right around 190-195 degrees under street driving, where load is sustained (minimal stops, throttle open, minimal braking. 45-55 MPH). The cooling system only peaked at 215 for a moment during a climb which required hard acceleration, and this temperature actually dropped halfway through this. I'm thinking the radiator had to bleed some coolant or air when this happened? After this, another, steeper sustained climb only provoked a response of 210. The tires. The new Thunderer Trac Grip M/Ts I replaced the Kanati Trail Hogs with are a welcome change. The Kanatis performed excellently, however were quickly succumbing to road noise and wandering with their end-of-life. The Thunderers are quiet, and dont particularly track into the grooves of the road, so the rig is very easy to control currently. The Bad: The OEM Transmission cooler: This one gets a U for unsatisfactory from me. Now that I can actually watch the transmission temps, I can tell you this dinky little think doesn't cut it for the short, crawl-y bursts this rig is used to. It does ok-is cooling the trans when the vehicle over 65MPH, but leaves a lot to be desired if your rig lives around 50MPH. The 545RFE spec sheet shows nominal temp around 175-210, with 230 being the "caution zone." On this run, the trans cooler read out around the 200 mark, moving all the way to 220 during one of the sustained hill climbs, to promptly drop down again afterwards. The only time it really performed adequately was during a jolt at 65 MPH, where it held the temp between 180 and 200. Please note, some WJs are outfitted with a tiny aux cooler, inline with the in-radiator cooling. I'll probably replace this aux cooler with something larger, perhaps the size of the Hayden oil cooler I installed previously? I don't think that would hurt. Overloading in the rear half of the suspension. With all the weight migrated to the rear of the vehicle, it has a visible bias towards the rear. I'm thinking new, heavier-rate rear coils to balance everything out. It does get a little fiddly currently when coasting, though it is manageable. One way or another, I need to level out the rear, and add more weight to the front. All in all, not too shabby for about an hours worth of driving. This loop is great for determining how things are performing, and how things should be changed.
  3. Welcome to Mohave County! I reckon I'm not the only one here anymore. Lol
  4. I also have an upgraded IRO adjustable A-Arm waiting to go in, I just ran out of time this weekend. I've decided to stay short arm on the rear since it still suits my needs just fine.
  5. If you would have told me during my 2017 Cooling overhaul that I'd be doing it again, well, I probably wouldn't have been surprised. The thing with trying out aftermarket parts such as the 2-core radiator that I had installed at that time is that you never really know how it's going to affect the rest of the system. The increase in fin density with having a radiator that is double thick, quite literally, leads to issues with the OEM cooling solution (of course being the traditional Jeep 5-blade clutch fan, with an electric helper fan). A popular up-and-coming solution that sprang up in 2018 was to install the 11 blade fan and clutch used in the early 2000's Ford Explorers, which were an easy swap in that moves easily double the air the OEM solution did. But after 3 years with an explorer fan, and 3 explorer clutches toast (two OEM and one aftermarket), I finally threw in the towel, and said to [HECK] with it, and started researching electric fans that could be swapped in as a direct replacement for the entire two-fan system. Fortunately, I was not the only WJ owner on this quest at the time, so group consensus partnered with real world experience. Aside from this, I had some other bits & pieces I wanted to add anyways, to it was just a matter of collecting everything together and installing it all methodically. It's the first time I've really had a chance to add mods and parts without a time limit. All in all, it took about 7 days for me to do everything. I spent a lit of time planning and measuring wire runs, and I created a complete harness for everything- color coded and all! Loomed it, and snaked everything into place. All in all, I'm quite pleased with everything thus far. Summertime of course will be the true test, but so far everything is looking great! I ended up needing to replace the radiator due to seepage from around the areas where the fins mate into the main tanks. I'm considering taking the old radiator to a shop to see if I can have it repaired or re-cored. Aside from a new radiator, I also picked up a "Worley" branded fan shroud (It comes with a fan, but I was a wee bit sketched out by a super cheap fan). I opted again for an all aluminum, 2-core radiator. Many opt for a SPAL branded electric fan, however I opted for a Flex-A-Lite model(238), since I was going to use one of their adjustable fan controllers anyways (31165). Given that I already had the front end torn down, I also opted to replace my Gates (metal impeller) water pump for a FlowKooler water pump. These ones have a slightly different impeller design, which could be described as both "larger" and "more aggressive." They claim that this design change allows the system to cycle coolant faster and generate higher head pressures, however I don't really have any tools to test this. I've heard good things from others with this pump, so I figured I'd give it a shot with all of the other things I was doing anyways. Did you know silicon coolant hoses require special worm-drive clamp? Standard hose clamps will chew them up. Also seen are the Oil temp sender unit, and the Coolant sender as well. I added a cheap seal between the shroud and the radiator to dampen vibrations and also better direct airflow. I also installed a 3 gauge pod from Lo-Tek inc, with a couple of Glowshift gauges, particularly Oil and trans temp. The third pod may eventually hold something like an airbag controller, or information display. ohh, shiny! The Lo-Tek 3-gauge pod matches into the Jeep very well, but the mounting holes are not placed very logically. Some finagling will be required. The Oil temperature is pulled from a sensor inline to the oil cooler, shortly before it. The trans temp sensor is also located inline shortly before the cooler. As great as the fan does at pulling air, the real star of the show is, without a doubt, the fan controller. This Flex-A-Lite unit has some great features other than simply turning the fan on at a fixed temperature. It also: -Has a "Soft Start" feature (waits to initialize the temp monitoring until the vehicle has been in "run" for 6 seconds) -Adjustable temperature -Soft fan start (Starts the fan at 60% power and ramps it up as necessary) -"Cooldown" feature (runs the fan for 30sec after the vehicle is shut off) -A/C Bypass (Turns on fan @ 100% power when A/C is on) -Fan Bypass- Force fan ON -Fan Bypass- Force fan OFF (AKA "Water crossing" mode) I installed two switches for the FORCE settings, controlling the ON/OFF bypass modes, I also installed an LED indicator light to show when the fan is running. This is wired inline with the fan itsself. With so many connections running between the engine bay, dash, and A-pillar, I decided to make up a proper harness, color coded it, and split it into 3 separate sections. It made it easier to run so many wires at once, kept the space down, and also made it easier to document the wires. Dash cam power was also re-routed to this harness, cutting that wiring down as well. I may need to go back and re-do previous wiring jobs with this methodology in the future! I was in the final planning stages for the last section of harness here. The wires up front run to Power for the fan controller, the fan, and signal & ground for the trans temp sensor. you can B A R E L Y see the loomed harness coming in from the dash, inside of the driver side headlight support. I also took down my headlight assemblies and replaced the marker lamps with Sylvania ZEVO LED bulbs. They weren't kidding when they say "Super Bright!" With everything function tested, with no leaks, I was able to add in my final addition... fresh rubber! With the Kanati Trail Hog A/Ts on the verge of death after 5 years of abuse, it was time for an upgrade! I managed to get a deal with these Thunderer Trac Grip M/Ts at 35/12.50/R17E! So far, surprisingly quiet for an M/T tire! Monday was also my 9th year anniversary of owning this rig, so it seems like perfect timing for something that makes 'er look so fresh again!
  6. I'm sorry to say I've been a bit lax at updating what I've done. Like many, I've spent much of this year inside, but I finally got the itch to complete some projects on the Jeep. I ended up removing my Rola roof rack to replace it with a custom made Goliath Off Road flat rack. This rack is a direct bolt-in and completely replaces the factory cargo rack, for a much sturdier overall rack, with a much more sleek profile. (I forgot to take a picture, so this is the actual store picture Goliath Off Road uses) I haven't re-installed any of my accessories onto it yet, as I determine which ones I actually need. I also took the time last weekend to revisit my dual battery system, and make some improvements. all in all, it has performed admirably, with the secondary battery finally losing it's charge after five years. The volatile nature of our weather means that the primary battery doesn't last long, and the temperature-based charging of the WJ means that both batteries generally see less charging through the summer because of this. I made the decision to move the primary battery, and the isolator solenoid to the rear. While I was at it, I also replaced the mains cables with a kit from JeepCables.com, which were a wee bit long, but otherwise very good quality. I have yet to replace the starter cable because I am not sure exactly how to route it, but that cable is still in very good shape, unlike the others. I also installed a 180A Alternator. (Solenoid's goooone) I made the decision to run fresh 0GA wire all the way back, for both terminals. Sure, I could ground completely through the unibody, but I always thought more ground was better. Both batteries now have a direct ground link, also. So along with the previous ground I installed in the back The temperature sensor was also relocated, so the PCM is still rechnically reading the live battery temperature from that sensor. Pardon the wire slop. I still have to figure out what to do with the extra length. Also, I plan to re-loom the wires so they aren't just going every which direction. All in all, works great, the batteries are receiving a more consistent charge, and the lead-acid batteries were swapped with sealed AGM batteries, so hopefully we see some serious longevity of life gains!
  7. So, we've encountered several setbacks cutting the new panels for the ceiling. For one thing, the old saying "They don't build them like they used to" comes to mind. As it turns out, there aren't as many "even angles" in this thing as you'd expect. LOTS of trick cuts to get panels to fit. Fortunately, you do somehow get used to it after a while. Drilling holes into the steel "Ribcage" to fasten the panels turned out to be a chore as well, several drill bits later, I've had to upgrade to a set of bits for hardened steel. On top of that, the holes themselves actually have to be tapped, as the screws can't shape the steel on their own. This, plus an industrial strength adhesive tacking the panels to the ribcage, makes for a tight fit with pretty much no vibration or rattling. This will be a very pleasant change, as the initial panels in the rear driver side, above the bed and kitchen, were not held in by hardware (the previous owner worked on the ceiling, and neglected to reinstall the hardware at some point... as I found out when I tore down the old masonite boards). The beadboard doesn't flex very well, so we are looking at possibly "kerfing" the panels towards the front where the boards are visible. Fortunately in this storage space not much is lost. The panels are painted and will have to be cleaned, please pardon the dirt here. As you can guess, this is a mighty dirty job! Currently trying to find an appropriate trim to cover the seams. The trim screws will also be painted to match. For most of this project, the rear A/C cowl has been hanging freely. I've hit my head on it several times. Now It's fastened up and no longer an issue. The new LED light fixtures are also nice and bright. Pardon our dust! This panel above the door was our first attempt at Kerfing. The result was a panel which was still a bit too rigid, but could indeed bend further before it finally started to split.
  8. With the engine and mechanical refits successful, we finally have momentum to update a bit of the interior. Talking to several other Travco owners, we've discovered that the ceiling "carpet" is definitely not original. Aside from sagging, it's extremely difficult to keep clean. Naturally we decided to tear it down! What we uncovered was an extremely heat soaked... masonite? Paper board? Which had white "crinkle" style texture to it underneath (similar to what many modern motor homes use today). Whoever had installed the faux carpet ceiling covers had simply used a spray adhesive to hold it in place. Six panels made up the living area, kitchen, and sleeping areas. The strange thing, the first three boards I uncovered were properly fastened into place, and the the three rear-most panels weren't being held up by... anything. We had always attributed the rattles this thing put out while driving to being old, but the panels were being suspended by failing glue and gravity for all this time! Having removed the heat damaged panels, you get a good look at the rig's "ribcage" of steel supports and trusses which gives the fiberglass shell it's rigidity. Another thing this has led to is the inspection of both the 12v and house electrical. It looks to be in good shape, and in fact, appears to have been replaced at some point in the motorhome's life. This is probably for the better as I've seen a few Travcos burn in the last few months due to the original electrical becoming faulty. (The storage cabinets above the sleeping area fold down into two additional bunks. We've never used this feature, but in theory would allow this beast to house 4 people and two kids. The fold down sections are being supported since their cabling was removed in order to rip out the old ceiling) After making a few tweaks to the wiring, it's nearly ready for it's new ceiling layer! We decided to go for a wood beadboard, painted in a light offwhite (which I cannot remember the name of for the life of me) Coming up, the Kitchen area will get a new counter top, A nicer-than-plain-wood backdrop, and a majority of the bathroom will have to be disassembled to repair a busted water main. It's good to be finally making visible progress on this machine.
  9. And now for something completely different: https://youtu.be/eTPCNcuOEkw I decided to spend a little extra and get something really nice and form fitting in form of Coverking seat covers! Pretty great fit, finish and quality so far. We'll see how the hold up.
  10. Thanks! The fresh coat of paint on the rockers took her from tired looking, back to sharp and ready for action. Speaking of which.... she is pretty much ready for action! All that's left is this and that, minor weekend jobs. Although, I am eyeing a new roof rack among other things...
  11. Well, the beautiful weather has really got me in gear! Last week I installed Sliders from Affordable Offroad: Which is something I should've gotten done a LONG time ago. I ended up spending a couple of hours straightening the rocker panels out, sanding them down, and re-coating them makes everything look pretty dang sharp. Really, this is something that should've been completed late phase 2 or early phase 3, before the rig took rocker damage. Fortunately, it was minor enough to not hinder the installation much. Which leads to today, a beautiful Saturday with not a cloud in the sky, barely a breeze, and a high of 70f, I set out to tackle the relocation of my driver's side brake line into it's proper place, OUTSIDE of the Iron Y, instead of through it, as I had done previously. Once I had this completed, I broke out my trusty coil compressors, and removed the front coils to investigate the installation of coil retainers. Now, the IronMan4x4Fab retainers come with no instructions, but based on the hardware provided, I suspect the intended process would include holes into each coil perch in order to accommodate the mounting hardware. I've had these in my garage for about a year, which gave me plenty of time to think about that.... Why not just use rivnuts and not (potentially) ruin the integrity of my coil perches? So that's what I did. The factory hole in the perch would do perfectly on the lower perches, but the uppers did require some slight widening. No problem. Made installation a breeze, and the coils are tight and secured now. And with that, the Jeep is pretty much ready to wheel again! I did discover that my upper radiator hose is starting to weep, so that's gonna have to be replaced soon.
  12. Soooooo, yeah. Rough Country's QD Sway Bar links are something often times reviewed as being cheap, especially since they seem to expire without much abuse. I have, however had a relatively good run with my set. The upper joint of the links are still good, so it really comes down to the hardware making noise. Instead of spending $100+ to buy new ones, I decided to fork out a couple of bucks towards new hardware to resurrect these links for a while longer. https://www.youtube.com/watch?v=k3lXFoCob_o
  13. Well, the rig has returned to us after several weeks of refit at a local mechanic shop. To say that she is running well... is an understatement. She received: A full tuneup, new belts, hoses, wires, plugs etc. re-cored radiator... since nobody makes these rads anymore! rebuilt fuel system, with proper "helper" electric fuel pump and regulator & custom hard fuel lines. The ORIGINAL in-dash A/C system has been brought back to life with a new compressor and hoses. Now running r134a and staying very, very cool. new turn signal switch front end re-lube new transmission and oil pan seals new valve cover seals new exhaust manifold seals & some work to reduce a tick/ leak on the passenger bank ... and now the cosmetic work begins. A water main break somewhere in the back calls for our attention, meanwhile we have acquired all of the beadboard paneling for the ceiling. We also decided to tile over the plain wood in the kitchen area, giving it a cleaner look while still looking "in place" In the meantime, I'm also doing research for vintage or "vintage styled" 12v lights. the six 12v "main lights" across the cabin are ridiculously small, and worn out anyways. The problems I face are simple, it seems like not many 12v fixtures deviate from plain white and clear, with a more "modern" look about them. I found a few companies who make vintage reproductions, but primarily of the late 80's fake-woodgrain florescent fixtures that everybody used at the time. Once the main is repaired, the ceiling retrofitted, we'll be ready to rip up the carpet and replace it. It will be replaced with some sort of laminate or hardwood, depending on what ends up being durable and easy to clean. It's good to have this project back on track again.
  14. And now, a review of the Mishimoto Thermostat I installed three years ago. Needs improvement, unfortunately.
  15. You remember that time about 4 years ago when I messed with LED headlight bulbs? I did it again, with better results.
  16. I very much like the idea myself. As long as the leg is adjustable!
  17. Sorry 'bout that, Scott. I was typing that whilst drinking my morning coffee and missed an "I." Didn't mean for that to sound snarky. ... "Before I gave you a definitive opinion," is what it was supposed to say. Now that I have seen the build video, here's my couple of opinions. I feel like I'd constantly hit myself on hinge mounted steps, though I do understand the practicality. I agree with you, I believe that the propane tank would pose a hazard in a narrow traverse. I also agree with Kris. There's a lot going on externally- especially in the lighting department. I like the awning, (and the RTT) but such things do definitely take a toll on weight and topheaviness of a vehicle. I know in my own case it wouldn't really be practical in my stage of life as a single, 5'11" guy who can just drop a twin mattress down inside the Jeep and sleep in relative comfort. I'm jealous of the drawer system, and the fridge. Especially the fridge. I too appreciate that things hold functionality it appears.
  18. I actually Ran into these guys in Sedona when I was doing the Shakedown for my re-worked suspension. I didn't get out and talk, but hey, I did get a wave and a thumbs up. These rigs get used, so I suspect that the parts came to be put on piece by piece in a more "Necessity is the mother of invention" type way. But also trying to keep it lookin' cool up front. I've always lived by the philosophy that "If there is a reasonable explanation for it, then it makes sense." In other words, I'd need to see a build video explaining the different additions and why they came to be before I gave you a definitive opinion.
  19. Today the Jeep received an addition which is both useful and functional! I purchased a Remote start system from Syracuse Synergy, a small company which specializes in setting up remote start systems which are about as close to plug and play as you can get! Pre-flashed for the platform and ready to rock, It comes with the remote start "brain" and bypass module already hooked together. All you have to do is wire it in, and program it to your key! A pretty reasonable price, too. They (well, he, I believe William is a one man operation) also give you any support you may require, via e-mail, Facebook, or even Text message. That being said, I reckon it's pretty fool proof. Here's the system I ordered from them. They also offer a more "basic" system which does not utilize a 2 way remote. http://syracusesynergy.com/product/rs2waywj/
  20. Well, we've all come this far, it'd be a shame to stop now! In my case, Alot of the things I test on the Jeep are a little less conventional in scope, like the Oil Cooler, Headunit, or dual-core radiator. I like being able to report back to a group and receive consensus on those mods. I keep this build page (and a "copy" build page on OverlandBound's forum constantly updated because I receive good feedback from both pages. I like ORP, I've met you guys (you are my friends) and I'd like to do more trails in the future. It's just a long road from where we were to being ready to roll again. Almost there.
  21. It actually comes with Play store right on the bugger when you buy it! It does come with a .apk installer as well. One of the major issues that the earlier units had with play was that alot of them used a strange Hybrid Android/WinCE abomination. It made it so that most apps couldn't recognize the unit as Android (because it technically wasn't). In this case, All of Joying's current models run pure Android, and the functions which required WinCE to run have been rewritten into apps, which I can say are so far pretty well thought out and function pretty well. As for the sleep debacle, I found out it's actually a limitation of the motherboard itself, and the way the CPU behaves when Android move into it's "sleep" behavior. Joying has other new units they are working on which do support sleep... or "Quick Boot" at they are calling it. Full cold boot of the unit takes about 30-45 seconds, so it's not too bad waiting. Once my next modification to the Jeep is complete, that won't even be a huge issue.
  22. After many years of abuse, I finally decided to go ahead and replace the Clarion CZ-302 which has powered the Jeep's audio system for many years now. In recent times, it's bluetooth functionality had become fairly cumbersome and problematic to use. Since Andriod connectivity was the primary reason I was interested in this HU originally, and the rise of cheap-ish Andriod powered head units becoming readily available, I figured I'd cut out the middleman and give one of these units a try: My first impressions of this Joying branded unit are relatively positive. The unit is extremely snappy, and handles media extremely well. The only thing that irks me about this unit is that it doesn't support a sleep function- a gift and a curse. It won't run the battery down when the vehicle is off, but this means it has to cold boot if the vehicle is off for more than a minute. The fortunate part is that cold boot is rather fast. I let the Jeep warm up for a minute or two in the mornings anyways, and after my next mod is installed, that will seem like less of an issue anyways All in all, it's an addition that could be great, or could bite me in the butt down the road. It does have a 2 year warranty, so that is helpful for a while. It's the great experiment, I suppose. I can say that playback, radio, and the like sound fantastic, especially when compared to the early Android units which had interference issues. The real test is gonna be seeing how it holds up to the abuse offroad. It appears to be sturdy and well-constructed, so that seems rather hopeful. Another bonus is that Joying has been extremely receptive in answering my questions on the unit. I hope it lasts a pretty long time, honestly. We'll see in time.
  23. Not a whole lot new to report. The cooling system, despite having a much higher overall capacity to stock, continues to self-regulate extremely well in the cold. I was afraid I'd have issues with "Engine too cold" CELs given the High flow T-stat, dual-core rad, and Explorer 11 blade clutch fan I put in at the end of the summer. I still feel like the oil cooler is probably doing good things, but we'll wait for that oil to come out in a week or tow and see if it has broken down much. In the meantime, some good shenanigans coming up hopefully for tax season, so stay tuned! Also I did a quick 3 year update video on the Kanati Trail Hog A/Ts. So here's that:
  24. Thank you for the kind words. So far, I can say that the Oil Cooler has been a good addition.
  25. Well, I got to drive the Jeep to Sedona on (last) Sunday and run Broken Arrow Trail. Overall the performance was excellent and the Jeep drove admirably. Driving to Sedona (4 hours each way), running Broken Arrow, and plenty of time at idle, The Jeep consumed about 25 Gallons of gas total. I punch the numbers into my calculator, and that averages out to about 16 MPG. Much better than my previous two trips, where I averaged 8 MPG, and 6 MPG the time before that. There was a pretty stark difference in performance, too. This time around, it seemed like her power curve was correct again and she commanded herself pretty dang well up the hills and across the valleys. It's starting to look like we are truly on the mend!
×
×
  • Create New...